{"product_id":"the-extractor-premium-120mm-12v-canopy-vent","title":"The Extractor — Premium 12V Powered Canopy Vent","description":"\u003cp\u003eThe Extractor is the premium version of our Single 120mm 12V Powered Canopy Vent — a purpose-built, filtered \u003cstrong\u003epowered 12V exhaust vent\u003c\/strong\u003e for the rear of a 4x4 canopy, and just as at home in a caravan, camper trailer or van. We took the same proven two-part design and, based on customer feedback, refined it into three parts so the filter is now a genuinely serviceable polyurethane foam air filter. It's also made stronger than the Single and upgraded where it counts: an industrial-grade IP67 Noctua fan, a stainless steel fan guard and a filter you can clean or change in minutes.\u003c\/p\u003e\n\u003cp\u003eIf the Single is the vent most builds start with, \u003cstrong\u003eThe Extractor\u003c\/strong\u003e is the one for builds that work hard — dusty corrugations, a fridge running all day, long trips and wet weather.\u003c\/p\u003e\n\u003cp\u003eThis is an \u003cem\u003eexhaust\u003c\/em\u003e vent. It works best with an intake elsewhere, so air has somewhere to come from — see \u003cem\u003e\u003cstrong\u003e\u003ca title=\"The Original\" href=\"https:\/\/ventit3d.au\/products\/asa-carbon-fibre-filtered-canopy-vents\"\u003eThe Original\u003c\/a\u003e\u003c\/strong\u003e\u003c\/em\u003e. A powered exhaust drawing against a passive intake gives you a genuine push-pull cross-flow rather than just stirring the air around.\u003c\/p\u003e\n\u003ch3\u003eWhy it's the premium option\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eNoctua NF-F12 industrialPPC-2000 IP67 fan\u003c\/strong\u003e — Noctua's industrial range, rated IP67 for water and dust, spinning to 2000 RPM with a rated airflow of 121.8 m³\/h and an MTTF of more than 150,000 hours\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplaceable 10 mm Uni filter\u003c\/strong\u003e — 45 PPI Unifilter polyurethane air filter foam, the same type of filter media trusted in off-road air intakes, compressed into the housing so air can't bypass it. Clean it out or replace it — built to be serviced\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStainless steel fan guard\u003c\/strong\u003e — protects the fan and fingers, and won't rust in coastal or wet conditions\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick filter change\u003c\/strong\u003e — just two bolts to remove. The fan box tilts up on a built-in hinge, you clean or swap the foam, and lower it back down. No unsealing, no removing the vent from the panel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrinted stronger\u003c\/strong\u003e — thicker walls, higher infill and a larger print nozzle for better layer adhesion, so the parts are tougher than the Single's and better able to handle corrugations, knocks and heat\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-way control\u003c\/strong\u003e — always on, temperature activated with an adjustable thermostat, or fully off to conserve battery\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlug and play\u003c\/strong\u003e — built-in 5.5 x 2.1 mm DC power jack with a right-angle connector supplied, no wiring loom to make up\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow profile\u003c\/strong\u003e — the outer housing stands just 42 mm off the panel at its highest and slopes away toward the top\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDownward-facing louvres\u003c\/strong\u003e on the outer housing, so rain and dust are not driven straight into the opening\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGlass fibre reinforced\u003c\/strong\u003e — \u003cem\u003e\u003ca title=\"Materials Guide ASA-GF\" href=\"https:\/\/ventit3d.au\/pages\/materials\"\u003e\u003cstrong\u003eASA-Glass Fibre\u003c\/strong\u003e\u003c\/a\u003e\u003c\/em\u003e outer housing, UV stable and heat resistant, with an ABS-Glass Fibre inner fan box\u003c\/li\u003e\n\u003cli\u003eBlack — white coming later, or available by request\u003c\/li\u003e\n\u003cli\u003eSuits 4x4 canopies, caravans, camper trailers, vans, trailers and fixed structures\u003c\/li\u003e\n\u003cli\u003eAustralian made, with free postage Australia-wide\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003eThe assembly is in three parts. The outer housing sits on the outside of the panel and stays low-profile. The Inner to Outer Vent Mount clamps to it through the panel, so the vent stays sealed in place. The fan box locates onto the mount and carries the Noctua fan, the stainless guard and the control electronics in their own sealed compartment under a snap-fit lid. Because the fan box is a separate part, you can open it to reach the filter without disturbing the seal on the panel.\u003c\/p\u003e\n\u003cp\u003eThe fan draws hot air out of the canopy, through the 10 mm Uni filter, and pushes it out through the outer housing. Because the outer housing's louvres \u003cstrong\u003eface downward\u003c\/strong\u003e, water running down the panel and dust thrown up off the road are far less likely to be driven into the opening — and when the fan is off, the foam is a second barrier against fine dust.\u003c\/p\u003e\n\u003cp\u003eA hinge at the top of the Inner to Outer Vent Mount and two M6 cap head bolts at the bottom secure the fan box firmly in place, clamping the filter foam evenly all the way round.\u003c\/p\u003e\n\u003cp\u003eSet the switch to \u003cem\u003ealways on\u003c\/em\u003e for constant extraction, or to \u003cem\u003etemperature activated\u003c\/em\u003e and the adjustable thermostat will cycle the fan as things heat and cool. Switch it off entirely when you are parked up and want to protect the battery.\u003c\/p\u003e\n\u003ch3\u003eWho it's for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRegular \u003cstrong\u003edirt road and corrugation\u003c\/strong\u003e travel, where fine dust is the enemy and a cleanable, replaceable filter earns its keep\u003c\/li\u003e\n\u003cli\u003eRunning a \u003cstrong\u003efridge\u003c\/strong\u003e all day — a fridge working against trapped heat draws more current and cycles harder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoastal, wet and humid\u003c\/strong\u003e use, where an IP67 fan and stainless guard hold up better over time\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCaravans, camper trailers and vans\u003c\/strong\u003e — storage tunnels, boots and front boxes that trap heat and stale air\u003c\/li\u003e\n\u003cli\u003eAnyone who wants to fit it once and not think about it again\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSingle 120mm or The Extractor?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cem\u003e\u003cstrong\u003e\u003ca title=\"Single 120mm 12volt\" href=\"https:\/\/ventit3d.au\/products\/single-120mm-12volt-canopy-air-vent\"\u003eSingle 120mm\u003c\/a\u003e\u003c\/strong\u003e\u003c\/em\u003e suits most standard builds and is the right starting point. Choose The Extractor if you travel dusty roads often, need the fan to survive water and grime, or want a filter you can service yourself.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSingle 120mm\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eThe Extractor\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eStandard 120 mm 12V fan\u003c\/td\u003e\n\u003ctd\u003eNoctua NF-F12 industrialPPC-2000, IP67 rated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan guard\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNickel-plated steel\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFilter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBasic built-in filter\u003c\/td\u003e\n\u003ctd\u003eUnifilter polyurethane air filter foam, 10 mm, 45 PPI\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eControl\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAlways on \/ temperature \/ off\u003c\/td\u003e\n\u003ctd\u003eAlways on \/ temperature \/ off\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCutout\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e105–108 mm round\u003c\/td\u003e\n\u003ctd\u003e120 x 120 mm with R37 corners — 114 mm hole saw, then trim the corners\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFeature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eVentit3D\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProduct type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePremium filtered powered exhaust vent\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaterial\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eASA-Glass Fibre outer housing, ABS-Glass Fibre inner fan box\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNoctua NF-F12 industrialPPC-2000 IP67 PWM, 120 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan speed\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e2000 RPM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan rated airflow\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e121.8 m³\/h (fan only, free air)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan static pressure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3.94 mm H₂O\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan rated life (MTTF)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMore than 150,000 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFilter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eUnifilter 10 mm foam, 45 PPI, replaceable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFan guard\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eStainless steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e12V DC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePower connection\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.5 x 2.1 mm DC power jack (right-angle connector supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended fuse\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eControl\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eThree-way — always on \/ temperature activated (adjustable) \/ off\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOuter housing\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e160 mm wide x 225.5 mm long (louvre end to top) x 42 mm high from the panel, all ±0.5 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eInner to Outer Vent Mount\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e148.8 mm wide x 224.5 mm long x 24 mm thick overall, all ±0.5 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDepth inside the canopy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAbout 56 mm from the inside of the canopy wall to the top of the installed fan box\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMain cutout\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e120 x 120 mm with R37 corners — cut with a 114 mm hole saw, then trim the shaded corners shown on the template\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFixing\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7 x M5 stainless button head bolts clamping the Inner to Outer Vent Mount to the outer housing, 7 x 5 mm drilled holes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eColour\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBlack (white coming later, or by request)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eApprox. 750 g, all three parts combined\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLouvre orientation\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eDownward facing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSuits\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e4x4 canopies, caravans, camper trailers, vans, trailers, structures\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePrimary use\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eRear canopy exhaust\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0915\/5097\/4236\/files\/the-extractor-outer-housing.png\" alt=\"Ventit3D The Extractor premium 12V powered canopy vent outer housing dimension diagram - 160 x 225 x 42 mm, 120 x 120 mm R37 cutout\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0915\/5097\/4236\/files\/the-extractor-inner-housing.png\" alt=\"Ventit3D The Extractor premium 12V powered canopy vent inner housing dimension diagram - 149 x 225 mm, 56 mm installed depth inside the canopy\"\u003e\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 x Inner fan box — fitted with the Noctua IP67 fan, stainless steel fan guard, three-way switch and thermostat\u003c\/li\u003e\n\u003cli\u003e1 x Inner to Outer Vent Mount — clamps through the panel to the outer vent and carries the fan box on its hinge\u003c\/li\u003e\n\u003cli\u003e1 x Outer vent housing — low-profile, with downward-facing louvres\u003c\/li\u003e\n\u003cli\u003e1 x 10 mm Uni filter — fitted between the Inner to Outer Vent Mount and the fan box\u003c\/li\u003e\n\u003cli\u003e1 x right-angle DC power connector\u003c\/li\u003e\n\u003cli\u003e7 x M5 stainless steel button head bolts — clamp the Inner to Outer Vent Mount to the outer housing\u003c\/li\u003e\n\u003cli\u003e2 x M6 stainless steel cap head bolts — hold the fan box closed; the two you undo to change the filter\u003c\/li\u003e\n\u003cli\u003e2 x 1:1 drilling templates — Inner Mount (recommended) and Outer Vent\u003c\/li\u003e\n\u003cli\u003e1 x installation and filter change guide\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitting\u003c\/h3\u003e\n\u003cp\u003eWe recommend taping the \u003cstrong\u003eInner Mount\u003c\/strong\u003e 1:1 drilling template to the \u003cstrong\u003einside\u003c\/strong\u003e of the panel, so you can see the canopy frame and any internal beams (the Outer Vent template is also supplied if you prefer to mark from the outside — both mark the same holes). Drill the seven 5 mm fixing holes, cut the main hole with a \u003cstrong\u003e114 mm hole saw\u003c\/strong\u003e, then trim the shaded corners to the finished \u003cstrong\u003e120 x 120 mm\u003c\/strong\u003e cutout (R37 corners). Then:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eApply sealant around the mating face of the outer vent housing.\u003c\/li\u003e\n\u003cli\u003ePlace the outer housing on the outside of the canopy with the \u003cstrong\u003elouvres facing downward\u003c\/strong\u003e — fitting it the wrong way up will let water in.\u003c\/li\u003e\n\u003cli\u003eFrom inside the canopy, run a small bead of sealant around the main opening on the face of the Inner to Outer Vent Mount that sits against the panel, and put a dab of sealant around each bolt hole. Then bolt the mount through the panel into the outer housing with the seven M5 stainless button head bolts, clamping the panel between them.\u003c\/li\u003e\n\u003cli\u003eFit the filter and hold it in place.\u003c\/li\u003e\n\u003cli\u003eFit the fan box onto its hinge at a slight angle, push it down and secure it with the two M6 cap head bolts. Don't overtighten them — a small drop of low-strength Loctite is recommended.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePower is plug and play through the DC jack. As with every electrical component in a canopy or caravan, fuse it — we recommend a 5 A fuse. A full installation guide is included in the box.\u003c\/p\u003e\n\u003ch3\u003eChanging the filter\u003c\/h3\u003e\n\u003cp\u003eJust two bolts to remove. Undo the two M6 cap head bolts at the bottom of the fan box and tilt the fan box up on its hinge. Lift out the foam and either clean it out or drop in a fresh 10 mm Uni filter, then lower the fan box back down and refit the bolts. The vent stays sealed to the panel the whole time.\u003c\/p\u003e\n\u003cp\u003eHow often depends on your conditions — check it more often if you travel dusty roads. Replacement filters: coming soon.\u003c\/p\u003e\n\u003ch3\u003eOften bought with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca title=\"The Original\" href=\"https:\/\/ventit3d.au\/products\/asa-carbon-fibre-filtered-canopy-vents\"\u003e\u003cem\u003e\u003cstrong\u003eThe Original\u003c\/strong\u003e\u003c\/em\u003e\u003c\/a\u003e\u003cem\u003e\u003cstrong\u003e \u003c\/strong\u003e\u003c\/em\u003e— side-mount intake pair, for a true push-pull cross-flow\u003c\/li\u003e\n\u003cli\u003eReplacement Uni filter (coming soon) — keep a spare in the glovebox\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/ventit3d.au\/products\/dual-10mm-cable-inlet\"\u003e\u003cem\u003e\u003cstrong\u003eDual Cable Inlet\u003c\/strong\u003e\u003c\/em\u003e\u003c\/a\u003e — weatherproof cable pass-through for the power feed\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant to note\u003c\/h3\u003e\n\u003cp\u003eThe IP67 rating belongs to the Noctua fan. The complete vent assembly has not been independently tested or rated. Any opening cut into a canopy, caravan or structure has the potential to leak if it is incorrectly installed, not properly sealed, submerged, or exposed to high-pressure water such as a pressure washer or car wash. You are responsible for correct installation, sealing, and periodic inspection for wear, damage and seal integrity.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat makes The Extractor the premium option over the Single 120mm?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eFive upgrades: an industrial Noctua NF-F12 industrialPPC-2000 fan rated IP67 for water and dust, a replaceable 10 mm 45 PPI Uni filter, a stainless steel fan guard, a hinged fan box that makes filter changes a two-bolt job, and stronger printed parts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs The Extractor IP67 rated?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe fan is. Noctua rates the NF-F12 industrialPPC-2000 IP67 for water and dust. The complete vent assembly has not been independently tested, so correct installation and sealing still matter.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat filter does it use?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA 10 mm Unifilter polyurethane air filter foam rated at 45 PPI (pores per inch), cut to fit and compressed between the Inner to Outer Vent Mount and the fan box so air can't bypass it. It can be cleaned out or replaced. Replacement filters are coming soon.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I change the filter?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eJust two bolts to remove. Undo them, tilt the fan box up on its hinge, clean or swap the foam and lower it back down. There's no need to remove the vent from the panel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow often should I change the filter?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIt depends on your conditions. Check it more often if you travel dusty roads, and clean it out or replace it when it looks clogged.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need a fuse?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. All electrical components in a 4x4 canopy should be fused. Even though The Extractor draws very little power, it is no exception. We recommend a 5 A fuse.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow does the temperature control work?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe same way as our Single 120mm. A built-in three-way switch lets you choose always on, temperature activated, or off. In temperature mode, the adjustable thermostat turns the fan on as things heat up and off as they cool. Power is plug and play through the 5.5 x 2.1 mm DC jack, with a right-angle connector supplied.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is The Extractor made from?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe outer housing is ASA-Glass Fibre — UV stable, impact resistant and heat resistant enough not to warp in a closed canopy in summer. The inner fan box is ABS-Glass Fibre, and the fan guard and mounting bolts are stainless steel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat colours is it available in?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eBlack to start with. White is coming later and is available by request.\u003c\/p\u003e","brand":"Ventit3D","offers":[{"title":"Black","offer_id":54745424658716,"sku":"Extract-01","price":330.0,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0915\/5097\/4236\/files\/The_Extractor_12V_Filtered_Canopy_Vent-_26.jpg?v=1792589395","url":"https:\/\/ventit3d.au\/products\/the-extractor-premium-120mm-12v-canopy-vent","provider":"Ventit3D","version":"1.0","type":"link"}